Visits: 86075814
AMS now reading: 1




Year 2008 No 2

Zifčák P., Brziak P., Balog M., Bošanský J., Srnka M.
THE INFLUENCE OF CREEP CONDITIONS TO MICROSTRUCTURE EVOLUTION AND SUGESTION OF PRECIPITATION CHANGES ASSESSMENT IN THE T24 STEEL
Keywords: steel T24|precipitation|carbides|
No 2 (2008), p. 195-208
  mag01.pdf (463 kB)
mag01_eng.txt (2 kB)  

Seidlerová J., Valášková M., Šustai O., Lešková J.
PHASE AND MORPHOLOGICAL CHARACTERISTICS OF METAL-BEARING MICROPARTICLES
Abstract
Due to their high iron content, fine-grained metal-bearing wastes are potential secondary raw materials whose utilization is restricted because of the contents of heavy metals. One of the conditions of recycling is a complete knowledge of phase and morphological structure of these materials. This paper deals with characterization of the dusts and sludge from metallurgical processes - the dusts from filters of electric arc furnace gas treatment plant, sludge from the filter press of an oxygen converter, and the dust from cast iron electro-filters. The experiments have shown that the steelwork dusts contain iron, mainly trivalent, as hematite, magnetite, franklinite and zincite. The lead is present as a sulphate and chloride. The compounds of cadmium were not detected. They are composed of particles smaller than 10 ?m, mainly spherical in shape. The majority of smaller particles are coagulated into clusters. In the steel work sludge examined, iron is mainly divalent, as wustite and nearly 7 % in metallic form. Contents of trivalent iron is only 3.7 wt. %. Beside wustite and metallic iron, the presence of hematite, franklinite, calcium dizinc hydroxide and calcite was proven. The steelwork sludge consists of unsymmetrical particles of different shape and size. Inhomogeneous, very small particles of Fe, Zn, Pb, Si, Mn, Mg, Al, Ca and O compounds are captured on the larger particles, which are composed of calcium carbonate or magnesium-calcium carbonate, or calcium hydroxide. The sludges from electrostatic filters from the cast iron production (two samples) contain in addition to iron, lead, cadmium and 10 wt. % zinc. The presence hematite, magnetite, franklinite, anglesite, and silica were proven in both samples. Lead chloride was detected only in one sample. Both samples contain ball-shaped, unsymmetrical particles and clusters of very small particles. Electron analyses prove that lead and cadmium compounds are present in smaller particles which are coagulated into clusters or adsorbed on iron or zinc iron oxides particles, or graphite.
Keywords: Fine grained metal-bearing wastes|Phase and morphology metallurgical wastes|
No 2 (2008), p. 209-223
  mag02.pdf (2 MB)
mag02_eng.txt (2 kB)  

Michalek K., Morávka J., Gryc K.
MODELLING OF TRANSFER PROCESSES IN GAS LADLE BUBBLING AND THEIR MATHEMATICAL IDENTIFICATION BY L-TRANSFORMATION
Keywords: steel|ladle|gas argon bubbling|stir elements|physical modelling|mathematical identification|
No 2 (2008), p. 224-232
  mag03.pdf (278 kB)
mag03_eng.txt (2 kB)  

Gulová L., Zemko M., Vlado M., Lászlo T.
SIMULATION OF PRODUCTION OF SELECTION DEFECTS IN ROLLING-PROCESS
Keywords: hot-rolling|cold-rolling|scores|overlaps|scratches|
No 2 (2008), p. 233-239
  mag04.pdf (1 MB)
mag04_eng.txt (2 kB)  

Nohavica D., Gladkov P., Jarchovský Z., Zelinka J.
DEFECT STRUCTURE MODIFICATIONS BY POROUS InP AND NON-IZOPERIODICAL HETEROJUNCTIONS GROWTH ON MICROPORES CONTAINING InP AND GaP
Keywords: Micropores in semiconductors|InP micropores|GaP nanopores|heat treatment|dislocations reduction|InAs/InP heterostructure|ZnO/GaP heterostructure|
No 2 (2008), p. 240-246
  mag05.pdf (346 kB)
mag05_eng.txt (2 kB)  

Donič T., Martikán M.
EVALUATION OF RESULTS OF COMPRESSION AND TENSILE ANALYSIS OF COMPACTS ON THE BASE OF 1 µM ALUMINIUM POWDER
Keywords: Compression test|Tensile test|Forward extrusion|Aluminium powder|Work-hardening exponent|Fracture analysis|Hollomon`s function|
No 2 (2008), p. 247-256
  mag06.pdf (289 kB)
mag06_eng.txt (2 kB)  

Bidulská J., Bidulský R., Kvačkaj, T., Bardi F., Evangelista E.
FORMABILITY EVALUATION OF ALUMINIUM ALLOY BY MEANS OF TORSION TEST AT LOW STRAIN RATE
Keywords: aluminium alloy|torsion test|formability|
No 2 (2008), p. 257-262
  mag07.pdf (179 kB)
mag07_eng.txt (2 kB)  

Blach J., Ševc P., Výrostková A.
INFLUENCE OF HYDROGEN ON STRENGTH AND FAILURE OF DISSIMILAR WELD JOINT OF Cr-Mo,V STEELS FOR ENERGY EQUIPMENTS AT TENSILE STRAIN
Keywords: Cr-Mo,V steels|hydrogen embrittlement|dissimilar weld joint|hydrogen induced cracking|tensile strain|cleavage failure|
No 2 (2008), p. 263-274
  mag08.pdf (397 kB)
mag08_eng.txt (2 kB)  

Sučik G., Hršak D., Fedoročková A, Lazić L.
THE PRELIMINARY CHARACTERIZATION OF SERPENTINITE FROM LJESKOVAC LOCALITY IN CROATIA
Keywords: serpentinite|lizardite|X-ray powder diffraction|differential thermal analysis|dilatometry|
No 2 (2008), p. 275-280
  mag09.pdf (193 kB)
mag09_eng.txt (839 B)  

Mišičko R.
PHYSICAL – METALLURGICAL FUNDAMENTAL CONCEPT OF CRACKING OF CONTINUOUSLY CAST PRODUCTS
Keywords: friction|stress|micro-crack|crack|peritectic transformation|austenite grain|dendrite|under solidus recrystallization growth|
No 2 (2008), p. 281-285
  mag16.pdf (53 kB)
mag16_eng.txt (1 kB)  

Gajdzik B.
THE PROCESS OF STEEL AND METALLURGIC PRODUCT DISTRIBUTION IN POLISH MARKET
Keywords: distribution of steel and metallurgical products|distribution channels|distribution networks|simultaneous marketing (SM)|
No 2 (2008), p. 286-291
  mag11.pdf (178 kB)
mag11_eng.txt (420 B)  

Kiss I.
RESEARCH AND EXPERIMENTS REGARDING THE MANUFACTURING OF METALLIC MATERIALS WITH A BETTER CUTTING CAPACITY
Keywords: researches|experiments|steels|metal constructions|sulphur addition|technology|improvement of the processing easiness|
No 2 (2008), p. 292-297
  mag12.pdf (70 kB)
mag12_eng.txt (1 kB)  

Mitrík V., Suchý T., Horváth L.
USING OF IGCC FOR COMBINED HEAT AND POWER GENERATION (COGENERATION)
Keywords: gasification|combined cycle|power generation|synthetic gas|emissions|
No 2 (2008), p. 298-301
  mag13.pdf (56 kB)
mag13_eng.txt (385 B)  

Forraiová L.
CHEMICAL ANALYSE OF FEMNC SLAGS
Keywords: slag from FeMnC production|bazicity|phase composition|
No 2 (2008), p. 302-306
  mag14.pdf (1 MB)
mag14_eng.txt (1 kB)  

Kiss I.
REJECT FORMS IN THE CAST IRON ROLLS PRODUCTION BETWEEN THE STATISTICAL RESEARCH AND TECHNOLOGICAL MEASURES IN FOUNDRIES
Keywords: cast iron rolls|reject forms|statistical analyses|hardness classes|rolls’ type|
No 2 (2008), p. 307-314
  mag15.pdf (159 kB)
mag15_eng.txt (1 kB)