Vydavatelia a tlač        Zameranie        Redakčná rada        Kontakt        Inštrukcie pre autorov        Abstrakčné databázy        AMS online      Ročník 2013      Ročník 2012      Ročník 2011 1 2 3 4      Ročník 2010      Ročník 2009      Ročník 2008      Ročník 2007      Ročník 2006      Ročník 2005      Ročník 2004      Ročník 2003      Ročník 2002      Ročník 2001      Ročník 2000      Ročník 1999      Ročník 1998      Ročník 1997                Konferencie        Linky                 Počet návštev: 86987454 AMS práve číta: 1 hľadať: podľa autora podľa názvu podľa kľúčového slova Ročník 2011 No 3 R. Pernis, J. Kasala DEFORMATION DISTRIBUTION IN ROLLING ZONE K. s.: rolling|relative deformation|deformation distribution|rolling invariable|resistance deformation| No 3 (2011), p. 150-157   mag01.pdf (97 kB) mag01.txt (908 B)   L. Pantělejev, O. Man, L. Kunz MICROSTRUCTURAL STABILITY OF ULTRAFINE GRAINED COPPER AT ELEVATED TEMPERATURE K. s.: ultrafine grained microstructure|copper|microstructural stability|electron backscattering diffraction (EBSD)| No 3 (2011), p. 158-162   mag02.pdf (349 kB) mag02.txt (645 B)   I. Kuběna, T. Kruml MECHANICAL PROPERTIES OF AL THIN FILM MEASURED BY TWO DIFFERENT METHODS Abstract Mechanical properties of an aluminium thin film were measured by microcompression and indentation tests. The microcompression technique combines preparation of specimens using focused ion beam (FIB) and compression test by a nanoindeter device. Cylindrical specimens were prepared by focused ion beam milling. The height of cylindrical specimens was about 2 ?m and their diameter about 1,3 ?m. The load and displacement were continuously measured during tests. The stress-strain curves were obtained in two representations. Stresses of the first plastic bursts were determined in both representations. Hardness and Young modulus were measured by indentation test using continuous stiffness method. Representative values of thin film were calculated. K. s.: thin films|focused ion beam|aluminium|nanoindentation| No 3 (2011), p. 163-168   mag03.pdf (394 kB) mag03.txt (763 B)   B. Plešingerová, G. Súčik, M. Fabián SURFACE AREA CHANGE OF KAOLIN CAUSING ANNEALING K. s.: minerals|kaolinite|dehydroxylation|metastable phases|surface area| No 3 (2011), p. 169-176   mag04.pdf (378 kB) mag04.txt (875 B)   M. Longauerová, P. Bekeč, M. Fedorová, S. Longauer INFLUENCE OF CASTING RATE ON PRECIPITATION OF PARTICLES BASED ON MICRO-ALLOYING ELEMENTS IN SLAB SURFACE ZONE K. s.: precipitation|slab|casting rate|TiNb microalloy steel|TiNb IF steel| No 3 (2011), p. 177-185   mag05.pdf (390 kB) mag05.txt (933 B)   R. Findorák , M. Fröhlichová, J. Legemza, F. Bakaj, M. Džupková POSSIBILITIES OF APPLICATION THE TITANIUM ORE INTO THE SINTERING MIXTURE K. s.: sintering|titanium|ore|concentrate|mixture| No 3 (2011), p. 186-192   mag06.pdf (325 kB) mag06.txt (1 kB)   Š. Michna, N. Naprstková THE MECHANICAL PROPERTIES OPTIMIZING OF Al - Si ALLOYS PRECIPITATION HARDENING AND THE EFFECT ON THE CHARACTER OF THE CHIP K. s.: aluminum alloys|precipitation hardening|mechanical properties|heat treatment|intermetallic phases| No 3 (2011), p. 193-199   mag07.pdf (962 kB) mag07.txt (1 kB)   P. Bella, J. Hašan, R. Kočiško, A. Kováčová, J. Sas, I. Hrebíček NUMERICAL SIMULATION OF EXTRUSION ELBOWS K. s.: extrusion|mandrel end|welded elbows|fibers| No 3 (2011), p. 200-206   mag10.pdf (312 kB) mag10.txt (713 B)   J. Petrík THE INFLUENCE OF THE LOAD ON THE QUALITY OF MICROHARDNESS MEASUREMENT K. s.: hardness test|microindentation|metal| No 3 (2011), p. 207-216   mag09.pdf (110 kB) mag09.txt (856 B)   ... © 2005 AMS HF TU Košice ...