Počet návštev: 86262494
AMS práve číta: 1




Ročník 2010 No 2

B. Buľko, J. Kijac
OPTIMIZATION OF TUNDISH EQUIPMENT
K. s.: tundish|continuous casting|water model|physical modelling|
No 2 (2010), p. 76-83
  mag01.pdf (772 kB)
mag01.txt (680 B)  

M. Kvačkaj, T. Kvačkaj, A. Kováčová, R. Kočiško, J. Bacsó
FINITE ELEMENT ANALYSIS OF DEFORMATION BEHAVIOUR IN EQUAL CHANNEL ANGULAR ROLLING PROCESS
K. s.: Equal channel angular rolling (ECAR)|Severe plastic deformation (SPD)|Finite element modeling (FEM)|copper|
No 2 (2010), p. 84-90
  mag02.pdf (640 kB)
mag02.txt (1 kB)  

A. Kováčová, T. Kvačkaj, M. Kvačkaj, I. Pokorný, J. Bidulská, J. Tiža, M. Martikán
THE MECHANICAL PROPERTIES PROGRESS DEPENDING ON STRAIN RATE AND LOAD INVESTIGATION DURING ECAP PROCESS
K. s.: copper|ECAP|strain rate|mechanical properties|flow stress|
No 2 (2010), p. 91-96
  mag03.pdf (114 kB)
mag03.txt (817 B)  

M. Varchola, M. Besterci, K. Sülleiová
QUANTITATIVE MICROSTRUCTURE ANALYSIS OF DISPERSION STRENGTHENED Al-Al4C3 MATERIAL BY EBSD TECHNIQUE
Abstract
The main aim of the present work was described quantitative analysis of microstructure of by electron backscatter diffraction (EBSD) technique of dispersion strengthened Al-Al4C3 material. It is a technique by which SEM can be used to evaluate the microstructure by crystallographic analysis based on the acquisition of diffraction patterns from bulk samples. Mechanical properties of dispersion strengthened materials depend on microstructural and substructural parameters, their changes at elevated temperatures and also on grain and subgrain matrix structures. From this point of view the most important microstructural parameters of matrix are size, shape, and misorientation of grains and subgrains and their annealing behaviour. Realized microstructure analyses of Al-Al4C3 material were evaluated from two experimental specimens annealed at different temperatures and times. Obtained microstructures were evaluated and compared. Annealing process has influenced the grain size, shape and orientation of experimental material. Grains size and angle grain boundaries were evaluated from acquired crystal orientation maps.

K. s.: EBSD|grain size|angle grain boundaries|misorientation|
No 2 (2010), p. 97-101
  mag04.pdf (373 kB)
mag04.txt (1 kB)  

L. Némethová, T. Kvačkaj, M. Fujda, R. Mišičko, J. Tiža, M. Kvačkaj
AUSTENITE GRAIN SIZE CHANGE OF Nb-V STEEL IN DEPENDANCE ON CONTROLLED ROLLING CONDITIONS
K. s.: plastic deformation controlled rolling|recrystallization|average austenite grain size (average AGS)|Nb-V steel|
No 2 (2010), p. 102-108
  mag05.pdf (108 kB)
mag05.txt (1 kB)  

I. Maková, M. Sopko
EFFECT OF BLASTING MATERIAL ON SURFACE MORPHOLOGY OF STEEL SHEETS
K. s.: cold working|surface structure|SEM|steels|
No 2 (2010), p. 109-115
  mag06.pdf (394 kB)
mag06.txt (746 B)  

V. Sinka
FSW JOINT MICROSTRUCTURE OF TWO HIGH STRENGTH ALUMINUM ALLOYS: A 2024 / A 7050
K. s.: friction stir welding|lap joint|joint microstructure|
No 2 (2010), p. 116-121
  mag07.pdf (590 kB)
mag07.txt (688 B)  

M. Kvíčala, A. Hendrych, O. Životský, P. Jandačka
THE INFLUENCE OF Cr, Mn AND Mo ELEMENTS ON CRACKS OCCURENCE IN LOW-ALLOYED Cr-Mo STEELS
K. s.: segragation|steels|rolling|microstructure|
No 2 (2010), p. 122-126
  mag08.pdf (435 kB)
mag08.txt (906 B)  

Zs. Vaszi, A. Varga, J. Šváb
THE NEW WAYS OF NATURAL GAS TRANSPORT AND THEIR EFFECT FOR SLOVAKIA
K. s.: natural gas|transit|LGN terminal|Nord Stream|Blue Stream|
No 2 (2010), p. 127-132
  mag09.pdf (234 kB)
mag09.txt (900 B)